設備概述

Summery

用途和特點/Purpose And Features

本機是為中、重無內胎車輪輪輞壓平面、沖氣門孔設計的專用雙動液壓機。

本機分為主機、動力機構和電氣控制箱三大部分，具有獨立的液壓傳動裝置和電氣控制箱。

采用PLC控制，可以實現手動調整、自動二種操作規范，并具有超溫保護、緊急停車、過濾器堵塞發訊等功能。This machine is a kind of special double-action hydraulic press which is used for valve hole flattening and punching of medium & heavy duty commercial vehicle rim.

This machine is composed of host device, hydraulic driving device and electrical cabinet.

Its operation can be controlled by PLC system which can switch between auto and manual, and has multiple functions including over temperature protection, emergency stop, filter clogging alarm and so on.

Its operating pressure, working speed and stroke range can be adjusted according to the requirements of technology and processing.

Its host device’s slider mounted 2 guide way which used for guiding, and the 2 guide way can bear eccentric force when slider suffer eccentric load, to avoid direct effect on the piston rod, to prevent the eccentric wear and strain of piston rod, so this design can increase service life of seal.

特點

本機的工作壓力、工作速度、行程范圍等可根據工藝需要進行調節。

本機滑塊有二根導軌進行導向，當滑塊受偏心載荷時，由二根導軌承受，避免直接作用在活塞桿上，防止活塞桿的偏心磨損和拉傷，提高密封壽命。

技術參數/Specification

設備型號	Model Number	YKQ-400-AH
壓平油缸公稱力	Nominal Press Force of Flattening Cylinder	630KN (P=25Mpa)
滑塊最大行程(可調)	Maximum Travel of Flattening Slider	320mm, adjustable
沖孔油缸公稱力	Nominal Press Force of Punching Hole	320KN (P=20Mpa)
沖孔油缸最大行程	Maximum Travel of Punching Cylinder	25mm
滑塊至工作面最大距離	Max. Distance between Slider Undersurface and Working Table Surface	670mm
滑塊尺寸	Slider Size	300mm×200mm
喉深	Throat Depth	225mm
工作臺尺寸	Working Table Size	W650mm×D635mm
工作臺到地面高度	Vertical Height from Working Table to Floor	750mm
滑塊快速下行速度	Fast Downward Speed of Slider	80mm/s
滑塊慢速工作下行速度	Lower Downward Speed of Slider	43mm/s ~ 17mm/s
滑塊回程速度	Return Speed of Slider	90mm/s
液壓電機功率	Hydraulic Motor Power	18.5Kw
	聯系電話：郝部長 15168866582

結構概述/Machine Structure

本機由主機、液壓傳動裝置和電器控制裝置三個部分組成，主機包括：機身、主缸。液壓傳動裝置包括油箱、油泵—電機組、集成閥等，電氣裝置包括電氣控制箱、電氣操縱箱等。主機和液壓傳動裝置安裝在混凝土基礎上，基礎見附圖所示，電氣箱安放在機身后面

The valve hole press machine consists of three parts: main machine, hydraulic transmission device, electrical control device. The main machine includes: lathe bed, main cylinder. Hydraulic transmission device includes oil tank, oil pump-motor group, pile-up valve etc. Electrical device includes electrical control box, electrical operation box etc. The main machine and hydraulic transmission device are installed on concrete foundation, which is shown on attached drawing. The electrical box is installed on back of lathe bed.